IEEE STANDARDS REFERENCE FOR INSULATION COORDINATION BASIC INFORMATION


ANSI C84.1-1995, Electric Power System and Equipment—Voltage Ratings (60 Hz).

ANSI C92.2-1987, American National Standard for Power Systems—Alternating-Current Electrical Systems and Equipment Operating at Voltages Above 230 kV Nominal Preferred Voltage Ratings.


IEEE Std 4-1995, IEEE Standard Techniques for High Voltage Testing.2

IEEE Std 24-1984, IEEE Standard Performance Characteristics and Dimensions for Outdoor Apparatus
Bushings.

IEEE Std 100-1996, IEEE Standard Dictionary of Electrical and Electronics Terms, Sixth Edition.

IEEE Std 516-1995, IEEE Guide for Maintenance Methods on Energized Power Lines.

IEEE Std 987-1985, IEEE Guide for Application of Composite Insulators (withdrawn).3

IEEE Std 998-1996, IEEE Guide for Direct Lightning Stroke Shielding of Substations.

IEEE Std 1313.1-1996, IEEE Standard for Insulation Coordination—Definitions, Principles, and Rules.

IEEE Std C2-1997, National Electric Safety Code

IEEE Std C37.04-1999, IEEE Standard Rating Structure for AC High-Voltage Circuit Breakers Rated on a Symmetrical Current Basis.

IEEE Std C37.48-1988 (Reaff 1992), IEEE Guide for Application, Operation, and Maintenance of High-Voltage Fuses, Distribution Enclosed Single-Pole Air Switches, Fuse Disconnecting Switches, and Accessories.

IEEE Std C57.12.00-1993, IEEE Standard General Requirements for Liquid-Immersed Distribution, Power and Regulating Transformers.

IEEE Std C57.12.01-1989, IEEE Standard General Requirements for Dry-Type Distribution and Power Transformers Including Those with Solid Cast and/or Resin-Encapsulated Windings (withdrawn).4

IEEE Std C57.13-1993, IEEE Standard Requirements for Instrument Transformers.

IEEE Std C57.21-1990 (Reaff 1995), IEEE Standard Requirements, Terminology, and Test Code for Shunt Reactors Rated Over 500 kVA.

IEEE Std C62.1-1989 (Reaff 1994), IEEE Standard for Gapped Silicon-Carbide Surge Arresters for AC Power Circuits.

IEEE Std C62.11-1999, IEEE Standard for Metal-Oxide Surge Arresters for Alternating Current Power Circuits.

IEEE Std C62.2-1987 (Reaff 1994), IEEE Guide for the Application of Gapped Silicon-Carbide Surge Arresters for Alternating-Current Systems.

IEEE Std C62.22-1997 (Reaff 1993), IEEE Guide for the Application of Metal-Oxide Surge Arresters for Alternating-Current Systems.

IEEE Std C62.92.1-1987 (Reaff 1993), IEEE Guide for the Application of Neutral Grounding in Electrical Utility Systems, Part I—Introduction.

Comments

Post a Comment

Popular posts from this blog

POLYMERIC INSULATON OF POWER CABLES BASICS AND TUTORIALS

This type of cable can be classified as follows: 1. NEC compounds 2. Elastomers 3. Thermoplastics 4. Thermosettings The rubber and rubber-like insulated cables enjoy their popularity owing to moisture resistance, ease of handling, ease of splicing, and extreme flexibility. Elastomers are materials that can be compressed, stretched, or deformed like rubber and yet retain their original shape. The thermoplastics materials soften when they are reheated, whereas thermosetting-type insulation has very little tendency to soften upon reheating after vulcanization. The earlier oil-based natural rubber compounds have been replaced by synthetic materials, which have better electrical and mechanical characteristics. The following synthetic rubber-like compounds are in use today: Ethylene propylene rubber (EPR) , an elastomer compound: EPR is commonly used in power cables, but is also gaining use in telecommunications and other types of cables. EPR possesses good chemical,...
Read more

ENTRY LEVEL and SENIOR ENGINEERING JOBS

Hello there. On this blog, i will try to compress and collect any available engineering jobs out there with emphasis on the entry level. USA JOBS 1 USA JOBS 2 USA JOBS 3 M.E. JOBS 1 M.E. JOBS 2 M.E. JOBS 3 note: I am in no way related to these job hiring poster.
Read more

SURGE ARRESTER ENERGY HANDLING CAPABILITY FOR TRANSMISSION AND DISTRIBUTION LINES APPLICATION TUTORIALS

Image
Photo Courtesy of http://www.classiclightningprotection.com/index.html Metal oxide arresters protect the equipment from high voltage surges by absorbing the energy from the surge. Hence, the energy handling capability (or also called "energy absorption capability" or "energy withstand capability") is an important consideration in the design and application of metal oxide arresters. Most manufacturers publish energy capability values of arresters. However, there are no specified tests either in IEEE/ANSI, or IEC standards. Hence, there is confusion in using these important application parameters. Both IEEE and IEC are contemplating writing standardized tests for the arrester energy handling capability. When metal oxide arresters are energized, valve elements of the arrester will absorb energy which results in a temperature increase of the valve elements. Under normal operating conditions (i.e. absence of overvoltage) there is a balance between the heat...
Read more
free counters